PHiliphh M4735A XL defibrillator power supply board M4735-40016
PCA control
The PCA controller performs the following functions:
System-wide processing.
System-wide clock and control functions including:
A. Check the power on/off sequence.
B. Save the configuration options created by the user.
C. Storage of operating software, including data used to create graPHiliphhilipics and display formats.
Important network pages among other features of the PCA.z user interface, including:
A.Generates and controls sounds and audio signals.
B. Generate and format real-time information for monitors and printers.
C. Check printer functions.
D. LED display control to set time, speed, AC power, battery charge.
Control data flow to and from the data card.
Power PCA defibrillation control features include:
A. Start the capacitor charging sequence.
B. Monitor the charge on the capacitor.
C.Start the download sequence.
control features on Power PCA including:
A. Start / stop stimulation.
B. User-selected rate and output control and delivered pacing current control.
Frontal ECG monitoring in parametric PCA (electrocardiogram) and power PCA (paddle/paddle electrocardiograPHiliphhilip).
5V logic power supply regulation and generation
| Item name | PHiliphh M4735A XL defibrillator power supply board M4735-40016 |
| Brand | PHiliphh |
| Model | M4735-40016 |
| Use place | Hospital Devices; Medical Care; ICU; |
| Deliver time | 3-5 days |
| Warranty | 90 days |
Power PCA
Power PCA performs the following functions:
1. Analogous front for ECG electrodes.
2. Impedance measurement for the Blade Connection Indicator (PCI) function.
3. Generation and control of pacing waveforms according to PCA control instructions.
4. Monitoring of pacemaker function as prescribed by the PCA for monitoring:
a)to charge the capacitor to the correct power level.
b) Power supply and waveform control
c) Discharge capacitor (discharge).
Removal
1. Disconnect the patient connector from the power supply PCA.
A. Disconnect the 9-pin connector and press the latch to release.
B. Tighten with the needle clamp to disconnect the two high pressure vane connectors.
2. Disconnect the battery PCA from the power PCA.
A. Disconnect the large white 4-pin connector and press the latch to release. This connector has four battery wires (two red, two black).
B.Disconnect the small 2-pin connector; Press the latch to release.
3. Disconnect the power supply.
A. Disconnect the 6-pin connector from the Power PCA and press the latch to release. Note that it only contains three wires.
B. Disconnect the 4-pin PCA connector from the power supply, press the latch to release.
4. Disconnect the controller PCA ribbon cable. Disconnect the large ribbon cable from the control PCA. The other end should have been disconnected from the control PCA.
5. Remove the power supply PCA.
A. Remove the 6-T10 screws from the Power PCA.
B. Lift the Power PCA and loop it around the patient interface and backrest.
Tip: Lift the back edge of the PCA (near the power supply) first. Then drive the PCA to the right to release the patient connector and case and lift the PCA out of the case
Parameter PCA
The PCA parameter performs the following functions:
1. Connect the ECG lead, ECG output cable, and SpO2 module.
2. Analog ECG terminal for 3 and 5 lead ECGs.
3. SpO2 on/off logic and patient isolation
Power Supply
The Power Supply provides regulated DC power to the unit and charges the Battery
If you're interested in P/N M4735-40016 PHiliphh M4735A XL Defibrillator Power Supply Board,feel free to contact us .Thank you .
Product Tags:
|
|
P/N M4735-40016 PHiliph M4735A XL Defibrillator Power Supply Board Images
|
